3D Bioplotter Research Papers

Displaying all papers by D. J. Schreyer (7 results)

Bioprinting Schwann cell-laden scaffolds from low-viscosity hydrogel compositions

Journal of Materials Chemistry B 2019 Volume 7, Issue 29, Pages 4538-4551

3D bioprinting techniques have been attracting attention for tissue scaffold fabrication in nerve tissue engineering applications. However, due to the inherent complexity of nerve tissues, bioprinting scaffolds that can appropriately promote the regeneration of damaged tissues is still challenging. This paper presents our study on bioprinting Schwann cell-laden scaffolds from low-viscosity hydrogel compositions including RGD modified alginate, hyaluronic acid and fibrin, with a focus on investigating the printability of hydrogel compositions and characterizing the functions of printed scaffolds for potential use in nerve tissue regeneration. We assessed the rheological properties of hydrogel precursors via temperature, time and shear rate sweeps,…

Characterization of Cell Damage and Proliferative Ability during and after Bioprinting

ACS Biomaterials Science & Engineering 2018 Volume 4, Issue 11, Pages 3906–3918

When a biomaterial solution containing living cells is subject to bioprinting, the cells experience process-induced stresses, including shear and extensional stresses. These process-induced stresses breach cell membranes and can lead to cell damage, thus reducing cell viability and functioning within the printed constructs. Studies have been conducted to determine the influence of shear stress on cell damage; however, the effect of extensional stress has been typically ignored in the literature until the recently collected evidence of its importance. This paper presents a novel method to characterize and quantify the cell damage caused by both shear and extensional stresses in bioprinting….

3D bioprinting of scaffolds with living Schwann cells for potential nerve tissue engineering applications

Biofabrication 2018 Volume 10, Number 3, Article 035014

Three-dimensional bioprinting of biomaterials shows great potential for producing cell-encapsulated scaffolds to repair nerves after injury or disease. For this, preparation of biomaterials and bioprinting itself are critical to create scaffolds with both biological and mechanical properties appropriate for nerve regeneration, yet remain unachievable. This paper presents our study on bioprinting Schwann cell-encapsulated scaffolds using composite hydrogels of alginate, fibrin, hyaluronic acid, and/or RGD peptide, for nerve tissue engineering applications. For the preparation of composite hydrogels, suitable hydrogel combinations were identified and prepared by adjusting the concentration of fibrin based on the morphological spreading of Schwann cells. In bioprinting, the…

Bioprinted fibrin-factor XIII-hyaluronate hydrogel scaffolds with encapsulated Schwann cells and their in vitro characterization for use in nerve regeneration

Bioprinting 2016 Volume 5, March 2017, Pages 1-9

The blood clotting protein fibrin contains cell-binding domains, providing potential advantage for the fabrication of tissue repair scaffolds and for live cell encapsulation. However, fabrication of fibrin scaffolds with encapsulated cells using three dimensional (3D) printing has proven challenging due to the mechanical difficulties of fabricating protein hydrogel scaffolds with defined microstructure. For example, extrusion based 3D printing of fibrin is generally unfeasible because of the low viscosity of precursor fibrinogen solution. Here we describe a novel technique for bioprinting of fibrin scaffolds by extruding fibrinogen solution into thrombin solution, utilizing hyaluronic acid (HA) and polyvinyl alcohol (PVA) to increase…

Use of the polycation polyethyleneimine to improve the physical properties of alginate-hyaluronic acid hydrogel during fabrication of tissue repair scaffolds

Journal of Biomaterials Science, Polymer Edition 2015 Volume 26, Issue 7, Pages 433-445

Recently alginate-based tissue repair scaffolds fabricated using 3D printing techniques have been extensively examined for use in tissue engineering applications. However, their physical and mechanical properties are unfavorable for many tissue engineering applications because these properties are poorly controlled during the fabrication process. Some improvement of alginate gel properties can be realized by addition of hyaluronic acid (HA), and this may also improve the ability of cells to interact with the gel. Here, we report improvement of the physical properties of alginate–HA gel scaffolds by the addition of the polycation polyethyleneimine (PEI) during the fabrication process in order to stabilize…

Novel crosslinked alginate/hyaluronic acid hydrogels for nerve tissue engineering

Frontiers of Materials Science 2013 Volume 7, Issue 3, Pages 269-284

Artificial tissue engineering scaffolds can potentially provide support and guidance for the regrowth of severed axons following nerve injury. In this study, a hybrid biomaterial composed of alginate and hyaluronic acid (HA) was synthesized and characterized in terms of its suitability for covalent modification, biocompatibility for living Schwann cells and feasibility to construct three dimensional (3D) scaffolds. Carbodiimide mediated amide formation for the purpose of covalent crosslinking of the HA was carried out in the presence of calciumions that ionically crosslink alginate. Amide formation was found to be dependent on the concentrations of carbodiimide and calcium chloride. The double-crosslinked composite…

Development of Schwann Cell-Encapsulated Alginate Scaffolds for the Repair of Peripheral Nerve Injury

CMBES Proceedings 35 2012

Nerve conduits for peripheral nerve repair have progressed from simple silicon tubes to complex engineered scaffolds. Recent advances in scaffold fabrication have enabled the incorporation of neurotrophins, extracellular matrix components and various cells into scaffolds for enhanced biologic properties. Bioplotting is one of the emerging methods, where the scaffold material, in form of a solution, is dispensed from a needle, layer by layer forming a three-dimensional structure. It enables the use of a wide range of materials, ranging from synthetic polymers (like polycaprolactone, polyglycolic acid, etc.) to naturally occurring polymers like alginate, chitosan, etc. Notably, the use of hydrogels gives…